0

Сравнение

VIP Club

Авторизуйтесь, чтобы ответить.

Вход  Регистрация 

Подключение Perreaux DP32 к ресивер Yamaha RX-V771

Здравствуйте!

Столкнулся с такой проблем.У меня есть Perreaux DP32, Perreaux P100 и ресивер Yamaha RX-V 771.Хочу подсоединит ресиверу к DP32 для домашное кино.На ресивере есть  pre out  7.2 /front surround,sur.back/  а на задную панель  на DP32 есть комутатор LINE/HT  для  COAX 2.Комутатор ставляю в положение НТ  и подключаю СОАХ2  к preout-front  ресиверу.Затим пользуюс обичайны аналоговы кабель. С  такое  подсоединение  звук выходит през фронтальные колоны и все выглядит нормально. Проблем  является в том, что когда переключаю источники на DP32/из СОАХ 2 на СОАХ1 или AUX 1 и т.д./ из колонках выходит очень сильное щелкание.Ресивер подключен еще к ТВ посредством оптики и к медиаплеер посредствoм HDMI.

Я писал об етом до инженеры от Перро и официально попросил ответ.Вот что ответили : One thing to check is the setting of the LINE/HT switch for AUX2 input on the rear panel. Please make sure it is set to LINE if you don't have a home theatre receiver connected or AUX2 input is not being used.


В юзер мануал тоже ничто не нашел ,толька ето: Aux2 Inputs

Operation of the unbalanced Aux2 input depends on the position of the Aux2 Function Switch.

With the switch set to ‘Line’ the volume control is enabled and accepts line level analogue audio signals from

source components with single-ended outputs such as iPods, tuners, phono stages and tape decks.

Note: These inputs are for analogue audio signals only. They should not be connected to the digital

output of a CD player or any other digital device.

With the switch set to ‘HT’ the volume control is bypassed and accepts pre out analogue audio

signals from home theatre receivers and surround processors allowing the Audiant DP32 to be easily

integrated into a home theatre system. Please ensure the volume level of the connected processor is

suitably attenuated before selecting this input.

Caution: When connecting a line level signal, make sure the Aux2 Function Switch is set to ‘Line’,

otherwise serious damage may occur to your amplifier and/or speakers.

14 Line Out

These unbalanced outputs provide a single-ended line level analogue audio signal, suitable for

recording the selected source input. The input should not be changed whilst recording.

15 Aux2 Function Switch

This switch is used to select ‘Line’ (normal) or ‘HT’ (home theatre loop) operation of the Aux2 input.

Прошу владельцы Перро, каторые встречали токой проблем о помощ.

Спосибо!

Извиняюсь для плохой руский!
Цитата
sageslt пишет:
Здравствуйте!

Столкнулся с такой проблем.У меня есть Perreaux DP32, Perreaux P100 и ресивер Yamaha RX-V 771.Хочу подсоединит ресиверу к DP32 для домашное кино.На ресивере есть pre out 7.2 /front surround,sur.back/ а на задную панель на DP32 есть комутатор LINE/HT для COAX 2.Комутатор ставляю в положение НТ и подключаю СОАХ2 к preout-front ресиверу.Затим пользуюс обичайны аналоговы кабель. С такое подсоединение звук выходит през фронтальные колоны и все выглядит нормально. Проблем является в том, что когда переключаю источники на DP32/из СОАХ 2 на СОАХ1 или AUX 1 и т.д./ из колонках выходит очень сильное щелкание.Ресивер подключен еще к ТВ посредством оптики и к медиаплеер посредствoм HDMI.

Я писал об етом до инженеры от Перро и официально попросил ответ.Вот что ответили : One thing to check is the setting of the LINE/HT switch for AUX2 input on the rear panel. Please make sure it is set to LINE if you don't have a home theatre receiver connected or AUX2 input is not being used.


В юзер мануал тоже ничто не нашел ,толька ето: Aux2 Inputs

Operation of the unbalanced Aux2 input depends on the position of the Aux2 Function Switch.

With the switch set to ‘Line’ the volume control is enabled and accepts line level analogue audio signals from

source components with single-ended outputs such as iPods, tuners, phono stages and tape decks.

Note: These inputs are for analogue audio signals only. They should not be connected to the digital

output of a CD player or any other digital device.

With the switch set to ‘HT’ the volume control is bypassed and accepts pre out analogue audio

signals from home theatre receivers and surround processors allowing the Audiant DP32 to be easily

integrated into a home theatre system. Please ensure the volume level of the connected processor is

suitably attenuated before selecting this input.

Caution: When connecting a line level signal, make sure the Aux2 Function Switch is set to ‘Line’,

otherwise serious damage may occur to your amplifier and/or speakers.

14 Line Out

These unbalanced outputs provide a single-ended line level analogue audio signal, suitable for

recording the selected source input. The input should not be changed whilst recording.

15 Aux2 Function Switch

This switch is used to select ‘Line’ (normal) or ‘HT’ (home theatre loop) operation of the Aux2 input.

Прошу владельцы Перро, каторые встречали токой проблем о помощ.

Спосибо!

Извиняюсь для плохой руский!
Здравствуйте!

К сожалению не знаком с Perreaux.
  • 1
Вступайте в закрытый клуб Pult.ru!
Подпишитесь на рассылку
и получите 500 бонусов 👋
Нажимая кнопку «Подписаться», я даю согласие на получение рассылок информационно-рекламного характера и обработку персональных данных.
Вы успешно подписаны!